How To Connect HP Deskjet 2622 To Wi-Fi?

Wireless printing eliminates the clutter created by messy cables and free the user from the confinement of printing from a single connected device. A wireless printer can connect to a mobile device with the same ease as it connects with a desktop or laptop. This simple post on how to connect Hp DeskJet 2622 to wifi will be very useful if you are attempting a new Hp printer wireless connection or if there is a connection error with a previously connected wireless DeskJet 2622 printer.

Pre-requisite for wifi connection
● Make sure you have the network information that is, the network name and its passcode.
● Your router is powered On and can access the network.
● The printer is placed within the vicinity of your router’s range.
● WiFi direct is disabled, as it won’t allow the wireless connection.
● Press and hold the wireless button and resume button at the same time to disable WiFi direct

Bring the printer to setup mode
For the first time installation, the hp printer remains in setup mode for two hours. In case you are reconnecting your hp DeskJet 2622 then you need to reset the network setting and configure the printer to setup mode.
● On the printer’s control panel press and hold the WiFi and cancel button simultaneously.
● Hold them both until you see the power button starts flashing.
● Release the button. The Hp 2622 DeskJet printer is now in setup mode and you can connect it to wifi.


Simple methods to connect Hp DeskJet 2622 printer to a wifi network

  1. Download and install the printer-specific drivers and software on your PC.
  2. Connect the printer to the same wireless network as that of your PC.
  3. Launch the printer software application, and on the connection screen select wireless.
  4. Follow instructions to finish the procedure, then close the application.
    Connect Hp DeskJet 2622 printer to WiFi via WPS
    You can easily connect the Hp printer to wifi using WPS (WiFi Protected Setup) connection mode:
    ● To enable the WPS mode press and hold the wireless button for about five seconds.
    ● The printer will remain in WPS mode for two minutes, so promptly press the WPS push button on your router too. Also hold it for two to three seconds to enable and initiate a WPS connection.
    ● If everything goes correctly, the wireless light will stop flashing indicative of a successful connection.

Connect Hp DeskJet 2622 printer to wifi using Hp smart app
● If you don’t have the Hp smart app download and install it from the Hp download webpage.
● When installed launch the app on your PC and Click on Printer’s icon. You will find it on the left panel of the screen.
● Select set up a new printer option. It will enable the discovery mode for your wireless network.
● The app will instruct you to download and install Hp printer drivers and software if not already installed.
● Click on the Continue button on the screen.
● Choose your Wi-Fi network, and provide the password if prompted.
● Now sit back. The rest of the process is automatic. The app will begin the setup process.
● If your printer is in Wireless setup mode it will detect the network and connect to it.

123.hp.com/ojpro 6978 printer Setup & Installation

Hp has developed several useful apps to assists its users with printer Setup and Installation. With hp easy start and hp smart, you can easily configure and install your 123.hp.com/ojpro 6978 printer. For the latest hp 6978 printer software and drivers download you can always head to the hp website.

123.hp.com/ojpro 6978 – Primary setup

Remove any packing material and sticking tape that your printer came in.

Apart from the printer, there will be, power chord, USB cable, ink cartridges instruction manuals, and installation CD. Check that nothing is missing.

Connect the printer to the power supply, wait for it to align all its components, and then open the ink cartridges compartment.

Remove the packing of the ink cartridges, and properly insert them in the corresponding slots. Check the instructions manual in case you have any trouble.

Open the paper input slot, adjust the width by sliding the paper width guide, and then load a stack of paper.

Use the USB cable to install your hp 123 Officejet Pro 6978 printer

  • Open a browser and enter 123.hp.com/setup.
  • This link will take you to the hp download page, click on the download button to download hp easy start file.
  • Double click on the file to extract and install the hp easy start software on your computer.
  • Now connect the USB cable to your computer and the printer. Launch the hp easy start, the software will detect the printer and show it on the screen.
  • Click on the continue button. The hp easy start will search for the latest software and drivers available for your printer.
  • When it finds the recommended software, click on the continue button to start the download.
  • When the download is complete the installer extracts the files and launch the installation.
  • When the installation is complete, your printer will be ready, and the hp printer assistant app will launch to further assist you with printing.
  • If your printer is not detected by the software go to the hp website and download and install the software and drivers for your hp printer’s model.

Setup hp Officejet pro 6978 wireless connection using Hp smart app

  • Go to 123.hp.com and download the hp smart app. When the download is complete install the app and launch it.
  • Switch on your printer. By default, the hp printer remains in Wireless setup mode for two hours after it was powered On for the first time.
  • But to manually connect the printer to the network, in case your printer does not support automatic wireless setup mode, go to the hp Officejet 6978 control panel’s display and select the wireless setup wizard.
  • The printer will search for the network and display it on the screen. Click on the name of your network.
  • When your printer is connected to your network, click on the plus sign button on Hp smart app screen to add the printer.
  • The app will detect the printer on your network and the display is on screen.
  • If your printer is not displayed, click on setup a new printer.
  • Now click on your printer’s model, and then click on the continue button.
  • A message will pop up asking permission to automatically access your wifi information. Click on the continue button to confirm.
  • Hp smart app will gather the network information and then complete the connection process.

Setup the Hp Officejet Pro 6978 printer on an android device

  • Enable the network setup mode through the printer’s control panel as mentioned above.
  • Open Google Play Store now, and install the hp smart app on your android phone.
  • Open the hp smart app and click on the continue button.
  • On the next screen click on the add printer button and then choose, Setup a new printer.
  • Click on your Printer’s name, and if asked to enter your network name and password.
  • Hp smart app will find the printer, when it will have all the information about the network, it will connect the printer and finish the installation.
  • Close the app and open the Google Play Store again.
  • Search the Hp print service plugin and install it.
  • Go to your phone’s settings, find the hp print service plugin, and enable it.

Setup the Hp Officejet Pro 6978 printer on an iOS device

  • Download and install the hp smart app on your iPhone and open it.
  • Enable the wireless connection mode on your 123.hp.com/ojpro 6978 printer.
  • Click on the option for setting up the printer on hp smart app and click on the continue button.
  • Now tap on the yes button to permit to bring the printer to the same network as your iPhone is.
  • Select your home network and enter the password. Now tap on Next to connect to the network.
  • The app will find the printer, connect it to the wireless network, and will display setup complete message.

Complete setup guide for 123.hp.com/dj2652 Printer

This guide will walk you through the whole 123.hp.com/dj2652 Printer Setup process. Make sure you follow each step in the sequence given here to avoid any blocks during the hp DeskJet 2652 installation.

The hp DeskJet 2652 model is an entry-level all in one printer, design to handle the basic day to day printing requirement and comes with print, scan, and copy capability. The printer supports both the wired and wireless connection type and even accommodate the latest hp auto wireless connect feature.

  • When you open the printer’s package box, you will find-
  • Hp driver and software installation media, usually a CD.
  • One power chord with an Adaptor, to connect the printer to the power supply.
  • A USB cable for connecting the printer to the computer.
  • Two ink cartridges, one for black and white printing, and one for coloured printouts.
  • User manual and setup guide for the Hp DeskJet 2652 printer.

All the mentioned accessories are necessary for the proper setup of your new hp printer. Although highly unlikely but if you find anything missing contact the vendor or the online marketplace from where you made the purchase, at the earliest, to get the printer package replaced with a complete set.

Hardware setup for hp DeskJet 2652 printer

  • Carefully remove the printer from the box and put it on a flat leveled surface.
  • Remove any sticking tape or packaging you find on the printer.
  • Pull open the ink cartridge cabinet, you will find sticking tapes there too, remove them.
  • When the printer is free from all the packaging material, insert the power chord in the power port, and then connect it to the power supply.
  • Switch on the printer, it will make some noises, don’t worry it’s the printer’s part aligning themselves.
  • The next step is to insert the ink cartridges but you must wait till the printer becomes idle, that is you don’t hear any noise coming from it.
  • Bring out the Cartridges from their packing, hold them carefully, and avoid any contact with the ink nozzle once you have removed the protective tape from them.
  • Now push the Cartridges inside their cabinet with ink nozzle pointing towards the printer. When you hear the snap sound, it means the cartridge is properly fitted in its place.
  • After this, raise the paper input tray, push the paper width guide to the left, and load some papers into the tray.
  • Slide-out the paper output tray and the extender. This completes the 123.hp.com/dj2652 printer hardware setup.

123.hp.com/2652 printer software setup

Once you have done the hardware part, move on to set up the hp printer software. Continue to the guide and you will learn how it is done.

  • Insert the software installation CD in the optical drive and let the setup install the hp printer software and drivers onto your computer.
  • Alternatively, you can download the software by visiting the 123.hp.com/setup or the 123.hp.com/setup 2652 page. The main benefit is that you will get the latest version.

Start the Hp DeskJet 2652 printer connection

Once you have completed the hardware and software setup for your hp 123 DJ 2652 printer, now it’s ready to connect to your computer. For the connection part you have two options:

  1. Wired connection via USB cable
  2. Wireless connection through your computer’s WIFI network.

The wireless connection also gives you two options, you can either connect through the Hp auto wireless connect which collects all your network information through your router to connect or you can opt for the WIFI Protected Setup, which employes the router’s WPS feature.

Wired Connection Via USB Cable

After the DeskJet 2652 software installation, run it, and when the connect screen appears, choose the connection type as USB.

  • Now insert the USB cable into the USB port of both the printer and your PC.
  • Wait for sometimes, you pc will check the connection status, setup the USB drivers and when done, will display the message, “the printer is ready.

Wireless connection with Hp auto wireless connect

On the connection window of the hp software choose the connection type as wireless and then click on the Hp auto wireless connect option.

  • For this connection type to work your PC’s operating system must have full control over the router as the network check will collect the required network settings to connect to your network.
  • Also, check that the led indicating the wireless connection is blinking.
  • Just the on-screen prompts and your printer will do the rest.

Wireless Connection Via WPS

Your router must have a WPS button for this connection type to work, so check it before proceeding.

  • Place the printer within the range of your router’s WI-FI network.
  • Now hold the wireless button on your hp Desk Jet 2652 Printer’s control panel till the LED indicating the wireless connection start flashing.
  • Now press the WPS button on your router and hold it for some time.
  • When the WPS connection is initiated, your printer will look for the network, and connect to it.
  • If the connection was successful, the wireless LED should have stopped flashing.

123.hp.com/ojpro 6978 printer Setup & Installation

Hp has developed several useful apps to assists its users with printer Setup and Installation. With hp easy start and hp smart, you can easily configure and install your 123.hp.com/ojpro 6978 printer. For the latest hp 6978 printer software and drivers download you can always head to the hp website.

123.hp.com/ojpro 6978 – Primary setup

Remove any packing material and sticking tape that your printer came in.

Apart from the printer, there will be, power chord, USB cable, ink cartridges instruction manuals, and installation CD. Check that nothing is missing.

Connect the printer to the power supply, wait for it to align all its components, and then open the ink cartridges compartment.

Remove the packing of the ink cartridges, and properly insert them in the corresponding slots. Check the instructions manual in case you have any trouble.

Open the paper input slot, adjust the width by sliding the paper width guide, and then load a stack of paper.

Use the USB cable to install your hp 123 Officejet Pro 6978 printer

  • Open a browser and enter 123.hp.com/setup.
  • This link will take you to the hp download page, click on the download button to download hp easy start file.
  • Double click on the file to extract and install the hp easy start software on your computer.
  • Now connect the USB cable to your computer and the printer. Launch the hp easy start, the software will detect the printer and show it on the screen.
  • Click on the continue button. The hp easy start will search for the latest software and drivers available for your printer.
  • When it finds the recommended software, click on the continue button to start the download.
  • When the download is complete the installer extracts the files and launch the installation.
  • When the installation is complete, your printer will be ready, and the hp printer assistant app will launch to further assist you with printing.
  • If your printer is not detected by the software go to the hp website and download and install the software and drivers for your hp printer’s model.

Setup hp Officejet pro 6978 wireless connection using Hp smart app

  • Go to 123.hp.com and download the hp smart app. When the download is complete install the app and launch it.
  • Switch on your printer. By default, the hp printer remains in Wireless setup mode for two hours after it was powered On for the first time.
  • But to manually connect the printer to the network, in case your printer does not support automatic wireless setup mode, go to the hp Officejet 6978 control panel’s display and select the wireless setup wizard.
  • The printer will search for the network and display it on the screen. Click on the name of your network.
  • When your printer is connected to your network, click on the plus sign button on Hp smart app screen to add the printer.
  • The app will detect the printer on your network and the display is on screen.
  • If your printer is not displayed, click on setup a new printer.
  • Now click on your printer’s model, and then click on the continue button.
  • A message will pop up asking permission to automatically access your wifi information. Click on the continue button to confirm.
  • Hp smart app will gather the network information and then complete the connection process.

Setup the Hp Officejet Pro 6978 printer on an android device

  • Enable the network setup mode through the printer’s control panel as mentioned above.
  • Open Google Play Store now, and install the hp smart app on your android phone.
  • Open the hp smart app and click on the continue button.
  • On the next screen click on the add printer button and then choose, Setup a new printer.
  • Click on your Printer’s name, and if asked to enter your network name and password.
  • Hp smart app will find the printer, when it will have all the information about the network, it will connect the printer and finish the installation.
  • Close the app and open the Google Play Store again.
  • Search the Hp print service plugin and install it.
  • Go to your phone’s settings, find the hp print service plugin, and enable it.

Setup the Hp Officejet Pro 6978 printer on an iOS device

  • Download and install the hp smart app on your iPhone and open it.
  • Enable the wireless connection mode on your 123.hp.com/ojpro 6978 printer.
  • Click on the option for setting up the printer on hp smart app and click on the continue button.
  • Now tap on the yes button to permit to bring the printer to the same network as your iPhone is.
  • Select your home network and enter the password. Now tap on Next to connect to the network.
  • The app will find the printer, connect it to the wireless network, and will display setup complete message.
hp-printer

6 Simple Steps for 123.hp.com/dj 2623 printer Setup &Installation

One could easily set up their new hp DeskJet 2623 printer, the only requirement is to follow one step after another. First hardware setup, then software installation, and then the printer’s connection to the computer. You can easily download the software and drivers from the 123.hp.com/2623 page, if you don’t have the installation media and to complete the remaining steps, Just follow this simple guide.

Step 1: Gather the components and prepare the hardware

  • For your new hp DeskJet 2623 printer,  you should make sure to remove all the packing tape first.
  • Note that the inside of the printer also has adhesive tape and more packaging material that can be easily overlooked. This could jam the paper when printing, so pay attention to this and check the inner compartment too.
  • Check to ensure that you have all the components which include cables and manuals that are listed in the box. These are needed for the Setup so check that you do not lack anything.
  • To begin, carefully take the printer out of the box and once everything is removed, place your printer in a horizontal position.
  • Gently lower the output tray, reach into the printer, then grasp the handle and lower the ink cartridge access door to open it.
  • Remove any packaging material you find here too and then close the access door to the ink cartridges.

Step 2: Connect HP Deskjet 2623 to the power supply

  • Locate the printer’s power cord between the components that you took out of the box. You will easily recognize it because one end has a standard electrical plug that goes into the power socket.
  • Now Go to the back of your printer and connect the power cable. The port is shaped like a number “eight” matching the end of the power chord.
  • Now Connect the power chord to a power source and press the ” ON ” button to switch on the printer.

Step 3. HP Ink Cartridges for HP Deskjet 2623 Printer

Your 123.hp.com/dj2623 printer uses two HP 65 ink cartridges. One black ink cartridge for normal black and white printing and one tri-color cartridge for colored printing.

  • The HP ink cartridges will be included in the box with your printer, find them, and remove their packaging. Be careful to only touch the plastic part on the ink cartridge
  • Lower the ink cartridge compartment door. You will see that the rail with the cartridge holder will move to the center.
  • You should wait until any moving part of the printer comes to completely still.
  • Once the printer is inactive and silent you can continue. Remove the plastic tape on the ink cartridges to expose the contact head.
  • Hold the cartridge by the sides, with the nozzles facing the printer, and then insert it into the corresponding slot.
  • Now slowly slide the new ink cartridge at a slight upward angle into the empty slot, and then gently push it down until it clicks into place. You will hear a snap sound.

Step 4. Load paper into HP Deskjet 2652 Printer’s paper tray

  • Raise the paper input tray and remove any traces of packaging that may have remained.
  • Slowly slide the paper width guides as far to the left as possible and gently push the stack of paper into the tray till it stops moving any further.
  • Now you may adjust the paper width guide to the right until it contacts the edge of the paper to correctly fit the width of the paper.
  • Lower the output tray and unfold the output tray extender.

Step 5. HP DeskJet 2623 Driver and Software Installation

Please do not try to connect the printer to your computer yet, you must wait until the printer software installation is complete and the software window prompts you to choose the connection type. That is why you do not need to connect even the USB cable yet.

  • Bring out the hp 2623 installation software CD included in the box.
  • Insert the installation disc in the disk drive. Either the Installer will start automatically or you can go to My Computer, locate the DVD drive, open it and run then run the installation program.
  • If case you don’t have the installation software or you have lost it, or you just don’t have an optical drive on your computer, open the following link 123.hp.com/dj2623 in a browser on your computer.
  • Download the hp 2623 printer software and then install it on your computer.

Step 6. Connect your 123.hp.com/dj2623 to your computer

  • For USB connection, when you are prompted to select the connection type on the hp printer software screen, select the USB option and continue the setup.
  • Insert the USB cable in the ports specific for USB on both your computer and printer.
  • Follow the instructions that are displayed on the screen to complete the setup.

Wireless Connection

First, enable the wireless connection feature on the printer. Press and hold the button for wireless connection until you see a light starts flashing.

  • From the connection type screen, on the hp printer software window choose wireless connection, and then if you see the hp auto wireless connection option, click on it.
  • Just do as the on-screen instructions tell you to. Information regarding your network will be exchanged between your computer and the printer.
  • If you don’t have the hp auto wireless connection option, you can opt for the wireless connection using a USB connection.
  • Connect the USB cable and then follow the instruction displayed on the screen.
  • Once the setup is complete remove the USB cable and print something to test the connection is working or not.

Proven Fixes for Driver Power State Failure on Windows 10 with HP Laptop

The dreaded blue screen of death on hp laptop. The one that
renders your laptop completely useless thereby putting a
complete halt on all important projects of yours. Although it
sounds like one big of an issue and truth to be told its indication
does justify its name as your hp laptop will have nothing but just a
blue screen, but when you understand the reason behind this
error and how it is caused, fixing it won’t be a problem. Blue
screen of death or the BSOD as its commonly known is a frequent
occurrence on laptop and computer including hp and usually
caused by the Driver Power State Failure. So to get rid of the
BSOD you have to understand what driver state power failure is
and how to fix it.
Driver Power State Failure – What is it?
The driver power state failure or controller power state failure as
the name suggest occurs when there is something wrong with the
drivers and the power state of your hp laptop. The issue presents
itself when you let your computer go to sleep mode but it does not
respond to the wakeup call and come back to the normal state
when you try. This creat a conflict that results in your computer’s
operating system responding with a blue screen. Faulty or
outdated display and wifi drivers are the most common culprit, but
other malfunctioning device drivers can cause this error too.
Best Methods to Fix the Driver Power State Failure in hp
laptop
As the most common reason for this error is outdated drivers, so
removing the faulty ones and then updating them to their latest
and compatible versions is usually the best way to fix the driver
power state failure in hp laptops. Other than that there some more
tweaks which you can apply that may help. So let’s jump right to
the solutions and correct this error.
Start the windows in the safe mode

As the blue screen does not let the computer boot properly and
without the working state of your pc it’s not possible to apply the
troubleshooting methods, we bypass the error and boot the
windows in safe mode. This will allow us to make changes and
apply the steps that will help us clear the blue screen and bring
back hp laptop to its normal working state. So first thing first, boot
the windows in safe mode.
● Restart your laptop. Due to the error, you will notice that
instead of booting the system is preparing for automatic
repair.
● Wait a few seconds, the startup windows repair screen will
appear. If your laptop doesn’t show the startup repair screen
restart it again.
● Once the startup repair window opens, select the advance
option, which will take you to another window.
● Here choose the troubleshoot option and under troubleshoot
again select advance option.
● From the advance option list, select startup settings and then
click on the restart button.
● When the windows boot up again, you will see the startup
settings screen with multiple options.
● Now press the number 4 key on your keyboard, this will
select the Enable Safe Mode option.
● The windows will restart again and this time it will boot in
safe mode.
Uninstall faulty drivers
You are in windows safe mode. Although the functionality of the
windows is limited, you can make the necessary changes that will
troubleshoot the issue.
● On your keyboard press, the windows and R key together to
open the Run dialogue box.
● To open the device manager screen type devmgmt.msc in
the Run box and click on the OK button.
● Look for any device listed with a yellow exclamation mark
against it.

● When you find one, right-click it and then from the menu
choose uninstall.
● This will eliminate the faulty drivers and uninstall them from
the system.
Update the drivers
Once you have removed incompatible and outdated drivers, you
can update them to the latest versions.
● Follow the same method as above to open the device
manager screen.
● Again look for the device with the yellow exclamation mark
and right-click them.
● This time select the update the driver software option from
the menu.
● For each driver, you want to update, select Search
automatically for updated driver software option.
● Restart the hp laptop when the whole process is finished and
hopefully the blue screen will be gone.
Adjust the hp laptop performance settings
As the driver power state failure could be due to power issues,
tweaking the laptop performance settings can also fix the error.
You should apply this method only if the issue persists even after
uninstalling and updating the drivers.
● Boot the windows in safe mode by following the method as
explained above and then open the run dialogue box.
● In the search field type powercfg.cpl and hit the enter button
to open the power settings window.
● Here click on change plan settings and then select change
advance power settings option.
● Double click on PCI Express or Graphic Settings or Link
state Power Management option. Only one of these options
will be displayed.
● A drop-down menu will open, select maximum performance
from the list. You should make this change for both the
plugged and battery option.

● Now double click on the power adapter setting and then to
power saving mode respectively and choose maximum
performance. Click on the apply button to apply these
changes.
● These settings will ensure that there will be no power
discrepancies. In simple words, your system will not go to
sleep mode thereby preventing the blue screen.
● Still, it’s not a permanent solution. You should make sure
that all the drivers on your hp laptop are updated to
permanently remove this error.

Hp Printer Driver won't install on Windows 10 | How to Fix it?

Drivers are an essential piece of software that enables
communications between the operating system and the hardware
or the Devices connected to the computer. What this means is
whatever device you are connecting to your computer you need
the drivers for that particular device to be installed for it to function
smoothly. Now every vendor for computer Devices provides
drivers for their peripheral through Offline media or online
downloads. Also, they release timely updates for any fixes or
adding more functionalities.
That is the case with hp printers too. No matter, whether it’s your
first hp printer setup or you are attempting a clean re-install you
need to install the hp printer drivers too. Now installing the drivers
is an easy process and didn’t take much time. You just insert the
installation media or download them online, then run the Installer
and wait for some time. That’s it, your printer will be ready to print.
Rather uneventful!
But there are certain scenarios where the hp printer drivers won’t
install on windows 10. Here things get complicated and windows
start showing all sorts of errors. At this point, one easy process of
hp printer driver installation on windows 10 becomes a nightmare
for users. Fortunately, though these errors can be resolved and
rather easily. Here we present tried and tested methods to quickly
fix the issue and get your printer back to running state.
Remove and reconnect the printer
This may seem old trick, a little outdated, but believe it or not, it
works. Also what harm there is to apply an old tweak, if it did
work, a lot of your precious time will be saved. That is why this is
the very first method we suggest.
● Switch off your printer and disconnect it from the computer if
you were using any cable such as USB or ethernet. Turn off
your computer too.

● Now do all the connections back again. Use a different USB
or ethernet port If possible because they might be causing
the issue.
● Connect the printer to the power supply and fire it on.
Restart your computer too and then reattempt the hp printer
driver installation.
● If the trick has worked you won’t see any error message
regarding the printer driver installation.
Try disabling the hp smart install software
To assist the hp printer’s drivers and software installation, hp in
past has bundled up its printers with software called the hp smart
install. Although the software is discontinued by hp, in case it is
installed on any computer it may create a conflict during the
installation process of hp printer’s drivers. Disabling it can resolve
the errors.
● On your printer’s screen, navigate to set up and then to
services.
● Here look for the Hp smart install feature and see if it is
enabled or disabled.
● If it’s enabled, then disable it and close the setup.
● Now check if you can install the hp printer drivers on your
Windows 10 device.
Remove any previous hp printer drivers and initiate a fresh
install
For a fresh install, you need to clean any previously installed
drivers. This eliminates any corrupt files that could be preventing
the installation of hp printer drivers on windows 10.
● On the desktop, double click the control panel icon to open
it. You can open it via the start menu too.
● Once in the control panel look for Hardware and Sound
select it and then click on devices and printers.
● Look for the Hp printer icon and select it. Now click on the
remove device option. Do it for any other hp printer listed on
the device and printer window.

● Now restart your computer and open the run dialogue box.
Use the shortcut Windows Key + R.
● Type Printui.exe /s in the search field and click on the OK
button.
● Printer Server Properties Window will open up. Click on the
driver’s tab, select all the listed hp printer drivers, and then
click on the remove button.
● Now try to install the driver again and see if the problem is
gone or not.
Run the Windows 10 troubleshooter program
To quickly fix minor troubles with windows 10, its creator,
Microsoft has embedded with it a troubleshooting program. In
case a user faces any issue this troubleshooter can diagnose and
rectify the issue. You can use this program to troubleshoot your
hp printer problem too.
● In the start, menu search for the settings option and open it.
● When the setting window opens up, select the Update and
Security option.
● On the left side of the screen, you will find the troubleshoot
option in the menu, click on it.
● Under this option choose printer and then click on the “run
the troubleshooter button.”
● Windows 10 troubleshooter will run a series of checks to
diagnose the issue that could be affecting the printer’s
function.
● If it finds anything, it will correct it automatically or suggest
the settings you must apply to clear out the error.
To sum it up
If you have applied all the fixes given here we are sure that by
now your issue must have been resolved. If still, hp printer driver
won’t install on windows 10 then it would we wise to contact the
hp support to fix it.

123.hp.com/setup

Hp support solutions framework usage and services

To ensure top-notch service to its users, HP has developed a robust
ecosystem focused on support and assistance. Goes by the name of HP
Support Solution Framework, this service offers a variety of tools to
ensure the proper functioning of HP computers and laptops. It comes
pre-installed on new HP desktops and notebooks, and is designed to
provide automated support, updates, and troubleshoots for HP PCs and
printers.
Why the need for Hp Support Solution Framework?
One could agree that no matter how reliable and robust a computer
product is, even from as reputed a brand as hp, it still prone to various
malfunctions during its lifetime. A possible Hardware failure, a software
glitch, or simply the need to update it are all instances that can
potentially decrease the productivity and put off user’s work. To
overcome these possible hindrances, HP has bundled up a series of
services in one framework that comes pre-installed with its products.
This application is called the HP Support Solution Framework and its job
is to manage hardware monitoring through dedicated software tools
and provide solutions through one single interface.

Hp Support Solution Framework Usage and Services
● Hp support Solution Framework is a set of tools built into HP
computers and printers. It can be utilized to monitor the proper
functioning of the computer, to alert the user in the event of a
breakdown or when the ink in the cartridges reaches a critical
level.

● HP Support Solution Framework also enhances the performance
and reliability through automatic product maintenance by
downloading necessary updates for drivers and software. Of
course, the user has full control over it. Updates are automatic
but users can also configure them to get notifications when
available.
● Another great thing about HP Support Solution Framework is that
it can resolve common errors with troubleshooting utilities and
automated fixes. And if the errors are above its capabilities, the
tool can help the user find hardware-specific support resources.
● Besides, the application allows you to manage HP peripherals
from the “My peripherals” tab. All you have to do is enter the
login credentials, or to create it if you don’t have one, to get
access to all the devices connected and registered in the tool. This
allows you to keep a tab on all the updates made or those to be
applied on all the connected devices.
Some Frequently Asked Questions about the Hp Support Solution
Framework
By now you must have a know-how of the hp support framework. In
order to make it more clear we are answering some of the most
common questions, user’s asked related to the framework.
How to access the Hp Support Solution Framework?
The framework is included on all HP desktops and laptops. Access to
the service is very simple you can do so by clicking on the question
mark icon in the Windows 10 taskbar. It is even possible to install the
tool on computers from other manufacturers for easy access. This could
include the support of resources and tools for HP printers. Once you are

on the main application window you can choose the various options
according to your need.
Is it necessary to have Hp Support Solution on your computer?
The simple answer to this question is No. It’s not necessary. But it’s
recommended. The whole idea behind the application is to provide the
user the ease with which it can keep its hp computer in good health. If
you can do the manual updates for your hp computer or you can
individually search for the solution and resolve the error that occurs
with your computer, you are better off without the application.
Otherwise, it’s best to have it installed on your hp computer.
Will it affect my computer if I uninstall the Hp Support Solution
Framework?
No, it won’t, if you have done the job properly. Your computer won’t be
affected. Also if the files are corrupted or infected with a virus, or it’s
taking up too much of memory and draining too much of CPU resources
then it’s better to remove it from your computer.
Can I re-install it if the need arises?
Yes, you can. You have to download the installation files for the Hp
Support Solution Framework from the hp website then you can install it
on your hp computer.
How can I uninstall the Hp Support Solution Framework?
The best way to completely remove the hp solution Framework
application is through the windows uninstall tool.

● Go to the control panel. You can find the icon on the desktop or
you can find it in the start menu.
● Here choose the programs and features option from the menu
and then select uninstall a program.
● From the list of all the installed programs, select Hp support
Solution Framework and right-click it.
● A drop-down menu will appear, here you click on uninstall. This
will start the uninstallation process, which will complete within a
minute.
● Close all the programs and then restart your computer to apply
the changes you have made.
Conclusion
That is all for the Hp Support Solution Framework. We hope that we’d
covered every detail. In case you need more information we would like
to point out to the hp customer support where any other additional
queries will be resolved promptly.

123.hp.com/OJ5258

Introduction

HP OfficeJet 5258 All in One Printer, Copier, Scanner and Fax Is your printer still tethered to your computer? Get with the 21st century with this do it all OfficeJet. You can print from anywhere on your network, even from your mobile devices. Take photos with your phone or tablet, send them to the printer and create magnificent fullcolor prints. You can also Scan receipts and bills and send them to your computer for easy archiving.

Benefits of OfficeJet 5258 printer

if you are thinking about to use OJ5258 printer than this thought is become a beneficial for your work . OJ5258 gives you flexibility in your office work or any kinds of projects work, makes your work easier also. By use of oj5258 you can make your project work more attractive and cool.

Features of OfficeJet 5258

  • You can easily get simple Wi-Fi setup in less than a minute, and start printing fast.
  • Have confidence in your connection with strong performance from dual band Wi-Fi.
  • You can easily print from a variety of smartphones and tablets.
  • Print more high-quality documents and photos with Original HP high-yield ink cartridges it’s such a beneficial.
  • Dual-band Wi-Fi for Reliable Connectivity; Supports dual -sided Printing to Save Paper; Compatible with HP 63XL High-yield Ink Cartridges.

Do wanna 123 HP Officejet 5258 Printer wireless connection

Here is the some instructions given below:

  • First to install the network drivers before proceeding further.
  • Detach the USB cable from the printer if connected already.
  • Turn on your router that is connected a network source.
  • Check the internet connection status and signal strength.
  • Turn on the Wireless feature on the on oj5258 printer
  • Now wait for a while and the printer displays a list of available networks.
  • Tap the network you want to associate with the printer .
  • Enable the Wi-Fi option in your computer or laptop.
  • Make sure to link it to the same network to which the printer is connected.
  • Choose a document or photo to print and start printing wirelessly.

HP OfficeJet 5258 Mobile Printing

The OfficeJet 5258 printer embeds dynamic mobile printing functionalities. It assent Android, iOS, and HP Wireless Direct applications. You print directly from your smartphone or tablet using any of the above- mentioned application.